These instructions apply only for IEEE 802.11^TM  Letter Ballot 89 (LB89) which is a procedural vote on Draft 6.0 of the Task Group “k” amendment to the current IEEE 802.11^TM standard.

Important:    YOU MUST FOLLOW THE INSTRUCTIONS BELOW!

This is a New Process we will be using to vote on letter ballots. It is a web based process similar to the process used for sponsor ballots. 

Failure to follow these instructions will result in your vote being discarded as an invalid vote.

This is a procedural letter ballot and the voter’s pool for this ballot is the IEEE 802.11 voters as of the start of the ballot.  This is a Procedural Motion and requires only a Yes, No or Abstain with no comments required for “no” votes. This will also require a greater than 75% approval to pass per IEEE 802.11 Policies and Procedures

The ballot opens October 13, 2006 at 23:59 Eastern Time USA and closes 15 days later on October 28, 2006 at 23:59 Eastern Time USA.

 and follow the instructions below:

You will see the following web page.

Note:  All fields, except for the FAX field, are required  in order for your vote to be valid.

IF THE ABOVE LINK DOESN'T WORK:

Please send an email for your vote using the following instructions:

Insert in the Subject field of the return email:

Vote-LB89-last name-first name-(Approve, Do Not Approve or Abstain)

(for example:  Vote-LB89-Doe-John-abstain)

ADDRESS YOUR EMAIL to: hworstell@research.att.com

                            with a CC to  stuart@ok-brit.com

                                                    apetrick@widefi.com

                                                    richard.h.paine@boeing.com  

Please fill out the balloter information that is requested.

CONFIRMATION WEB PAGE:

If you are submitting comments, click on the “Submit Comments” button.

TO SUBMIT COMMENTS:   

This will take you to a page that looks similar to this:

Select ONLY #2 - “File Upload”

Once selected, Click the “Continue to the Submit Comments Area”.

This takes you to the page below:

Email Confirmation:

You will automatically receive an email confirmation of your vote.

 

(Message sent via IEEE Standards webmail)

-----------------------------------------

Here is a courtesy copy of a ballot for IEEE 802.11 k Letter Ballot 86 just submitted:

 

# Ballot/Comment Data for 0000001 (IEEE 802.11 k Letter Ballot 86) # Submitted

Tue Aug  8 21:47:29 EDT 2006 # Type: ballot # Record Number: 112

 

ballot_code = 0000001

form_type = ballot

balloter_id = 112

name = John Doe

email = j.doe@xyz.com

phone = 555-555-5555

fax =

org = XYZ

vote = Approve, no comments (Y)

-----------------------------------------

(End of IEEE Standards webmail message)

Completing the Comment Form:

Should you wish to submit comments, please use the following instructions:

0)       Form:  The official comment form for Letter Ballot 89 must be used.  This comment form is available at http://www.ieee802.org/11/LetterBallots/LB89/LB89_CommentForm.xls

1)       Names: In the header of comment response form, please fill in your name in the <First Name>, <Last Name> fields.  Do not use your initials or anything else.

2)       Clause Column: This is the section number of the draft that your comment applies to - e.g. 2.1 or 4.2.3.  If you have a comment that applies to the entire document put "General" in the section field. Don’t put “all”, “many”, “various” or any other word you may personally fancy. If the field contains anything other that a clause number or “General”, the comment will be discarded and your vote possibly invalidated.  If your comment relates to a table, place the clause in which the table resides in this column and not the table number.  Put only the clause number and not the words, e.g. “clause”.

3)       E/T Column: Please use an E or T only to indicate a technical or an editorial comment. Please use upper case only so things sort right when we get all done.  Incorrectly categorized comments will be re-categorized by the Task Group chairperson.

4)       "Part of No vote” Column: If you say "no" in this column, we will feel free to skip that comment in terms of formally satisfying a "NO" vote. For any comment that is not part of your “NO” vote, mark it as "not part of a no vote" by entering “no” in the column. Any voter that votes “NO” should have at least one comment marked “yes” as part support for their “NO” vote.  Any voter that votes “YES” should not have any comments marked “yes” in this column.

5)       "comment/explanation" and "recommended change" columns: These are pretty self explanatory. If you do not recommend a change the comment may be skipped as you have not asked the group to do anything. Please keep the explanation of the comment separate from what you want done as a result of your reasoning. The voting group is too large for the task group to be interpreting what you are requesting.   Please remember that the operating rules state that all “No” votes MUST be accompanied by comments which include specific reasons and enough information for the group to understand what you desire in order to change your “no” to a “yes”. Simply saying “not good enough” is insufficient as the task group cannot reasonably be expected to understand what would satisfy the commenter and so invalidation of the vote is justifiable.

6)       Draft line numbers: If you choose to include a page / line number reference in your comments, please do so by putting is as text at the start of your comment. Do NOT put this info in the section number field. The rational is that the page/line numbers are valid only for the balloted draft version.  The section numbers are more likely to still be correct in later versions.

Stuart J. Kerry

IEEE 802.11^TM WG Chair

E-mail: stuart@ok-brit.com

Richard Paine

IEEE 802.11^TM TGk Chair

E-mail: richard.h.paine@boeing.com  

Harry R. Worstell

IEEE 802.11^TM Vice Chair / Balloting Coordinator

E-mail: hworstell@research.att.com  

October 13, 2006