Re: [STDS-802-11-TGBE] [20/1293] D0.1 Spec Text Preparation: Reminder fo

Thread Links	Date Links
Thread Prev	Thread Next	Thread Index	Date Prev	Date Next	Date Index

Thanks Youhan, that’s fine.

Regards,

Ron

From: Youhan Kim [mailto:youhank@xxxxxxxxxxxxxxxx]
Sent: Wednesday, September 09, 2020 10:11 PM
To: ron.porat@xxxxxxxxxxxx; STDS-802-11-TGBE@xxxxxxxxxxxxxxxxx
Subject: RE: [STDS-802-11-TGBE] [20/1293] D0.1 Spec Text Preparation: Reminder for POCs

Thanks, Ron.

I thought about it, but it is not ‘trivial’. For this particular section (34.X1.Y1. Scope), it is trivial – just write that PSDUs are mapped to PPDUs in case of A-PPDU. But then, we have to define A-PPDU somewhere else (Clause 3 definition? Clause 34 introduction? Some subsection under Clause34 to describe A-PPDU in more detail?). I didn’t see any section assigned to do that yet, and I don’t think that will be a easy/quick thing to write. And given that A-PPDU is an R2 feature, I would suggest that we defer writing that to a later point in time.

Regards,

Youhan

From: Ron Porat <000009a0da80e877-dmarc-request@xxxxxxxxxxxxxxxxx>
Sent: Wednesday, September 9, 2020 3:35 PM
To: STDS-802-11-TGBE@xxxxxxxxxxxxxxxxx
Subject: Re: [STDS-802-11-TGBE] [20/1293] D0.1 Spec Text Preparation: Reminder for POCs

Hi Youahn,

Please see a comment on 1293:

Document number/Revision	Comment	Page No.	Subclause	SFD reference	Proposed Change (if applicable)
11-20-1293-01-00be-pdt-phy-scope-and-eht-phy-functions	a) A function that maps the PSDU received from the MAC into a PPDU for transmission to one or more receiving STAs Doesn't cover A-PPDU, with multiple PPDUs.	1	34.X1.Y1	Motion 112, #SP48, [17] and [22]	Add A-PPDU function

Thanks,

Ron

From: Youhan Kim [mailto:youhank@xxxxxxxxxxxxxxxx]
Sent: Tuesday, August 25, 2020 4:26 PM
To: STDS-802-11-TGBE@xxxxxxxxxxxxxxxxx
Subject: Re: [STDS-802-11-TGBE] D0.1 Spec Text Preparation: Reminder for POCs

Hi, Alfred, Sigurd and Tianyu,

Please add the following draft text documents to the PHY agenda.

11-20/1293: PDT PHY – Scope and EHT PHY Functions

11-20/1295: PDT PHY – Overview of the PPDU encoding process

11-20/1294: PDT PHY – EHT PLME

Thank you.

Regards,

Youhan

From: Bin Tian <btian@xxxxxxxxxxxxxxxx>
Sent: Tuesday, August 25, 2020 4:16 PM
To: STDS-802-11-TGBE@xxxxxxxxxxxxxxxxx
Subject: Re: [STDS-802-11-TGBE] D0.1 Spec Text Preparation: Reminder for POCs

CAUTION: This email originated from outside of the organization.

Hi Alfred, Sigurd and Tianyu

Please add the following draft text to the PHY agenda

1153r1 PDT-PHY-Timing-Related parameters

I have uploaded the r1 which corrects a few errors/typos (Thank Shimi for pointing them out!) and removes the content related to CBW240

Thanks,

Bin

From: Wook Bong Lee <wookbong.lee@xxxxxxxxxxx>
Sent: Tuesday, August 25, 2020 7:59 AM
To: STDS-802-11-TGBE@xxxxxxxxxxxxxxxxx
Subject: Re: [STDS-802-11-TGBE] D0.1 Spec Text Preparation: Reminder for POCs

CAUTION: This email originated from outside of the organization.

Hi Alfred, Sigurd and Tianyu,

Can you please add following three documents in PHY agenda?

11-20/1252r0, PDT-PHY-Frequency Tolerance, Wook Bong Lee (Samsung)

11-20/1253r1, PDT-PHY-Modulation Accuracy, Wook Bong Lee (Samsung)

11-20/1254r1, PDT-PHY-Receive specification: General and receiver minimum input sensitivity and channel rejection, Wook Bong Lee (Samsung)

Best regards,

Wook Bong Lee

From: Alfred Asterjadhi [mailto:asterjadhi@xxxxxxxxx]
Sent: Monday, August 24, 2020 4:16 PM
To: STDS-802-11-TGBE@xxxxxxxxxxxxxxxxx
Subject: [STDS-802-11-TGBE] D0.1 Spec Text Preparation: Reminder for POCs

Hello all,

This is a gentle reminder that when you have spec text ready for a particular subclause/topic then the POC should request the respective chairs (MAC/PHY/JOINT) to [add the contribution to the agenda] and run a SP for including the prepared spec text to TGbe D0.1. Quoting the particular bullet from the guidelines that deals with this aspect:

· When the spec text for a particular subclause/topic is ready then the POC should request the respective chairs (MAC/PHY/JOINT) to run a SP for including the prepared spec text to the D0.1 of 11be.

o The document that is planned to be ran should be posted in the server for at least 7 days prior to running the SP.

o If the SP is approved then the TGbe editor will include the spec text to the draft, otherwise the spec text will not be included in its current form.

o The deadline for completing this task is set for September 1^st 2020 (EOD ET).

o Note: Figures should be provided to the editor in visio format (monochromatic).

Please let me know if you have any questions and/or suggestions.

Best Regards,

Alfred

To unsubscribe from the STDS-802-11-TGBE list, click the following link: https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-11-TGBE&A=1