Re: [10GBT] Request for Cat6 Emissions Characteristics
Hi All,
Here is the fixed matlab code and the fixed PDF file. The earlier code was
missing a sqrt(fs) normalization to account for the fact that only a single
pulse was being used for the PSD computation. I've also deleted the 20log10
"EMI PSD" computation, for the reasons I outlined earlier.
Sorry for the confusion.
Regards,
Sailesh Rao.
srao@phyten.com
>From: "Booth, Bradley" <bradley.booth@INTEL.COM>
>Reply-To: "IEEE P802.3an" <STDS-802-3-10GBT@listserv.ieee.org>
>To: STDS-802-3-10GBT@listserv.ieee.org
>Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
>Date: Thu, 22 Jul 2004 12:44:36 -0700
>
>Sailesh,
>
>Thanks for the concern about the Task Force Chair, but I'm not too
>concerned about the Working Group suddenly turning into a bunch of
>cannibals. :-) If there is going to be an emissions issue, let's get it
>out in the open now (no pun intended).
>
>Thanks,
>Brad
>
>-----Original Message-----
>From: stds-802-3-10gbt@IEEE.ORG [mailto:stds-802-3-10gbt@IEEE.ORG] On
>Behalf Of sailesh rao
>Sent: Thursday, July 22, 2004 8:54 AM
>To: STDS-802-3-10GBT@listserv.ieee.org
>Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
>
>
>Jose,
>
>You appear to have a valid point. I'll check the scaling used in these
>matlab functions and get back to you.
>
>However, for the sake of this task force chair, I hope you are wrong. If
>I
>have to lower the 1000BASE-T PSD by ~10dB, I'm afraid that some members
>of
>our working group will eat Brad Booth alive on the 10GBASE-T emissions
>issue.
>
>Meanwhile, I renew my request to Scott Powell to please publish a file
>version of the emissions characteristics he used to compute the contents
>of
>slide 6 of powell_1_0704.pdf.
>
>Regards,
>Sailesh Rao.
>srao@phyten.com
>
>----- Original Message -----
>From: "Jose Tellado" <JTellado@TERANETICS.COM>
>To: <STDS-802-3-10GBT@listserv.ieee.org>
>Sent: Wednesday, July 21, 2004 7:10 PM
>Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
>
>
> >Sailesh,
> >
> >There must be something wrong with the code, when the integral of the
> >1GBaseT PSD power is 15dBm (details below).
> >
> >I thought I gave you a good hint, and I rather you debug your code.
> >
> >The problem is likely in your modeling of the digital/analog sampling
> >rate conversion, lines 12-35.
> >You can check the 3rd chapter of (or any other introductory DSP book):
> >Oppenheim and Shafer, "Discrete Time Signal Processing". It's eq (3.49)
> >in my undergrad international edition.
> >
> >Jose
> >
> >
> >1GBase-T power details:
> >
> >10*log10(sum(10.^((f5mag-116)/10)))+60 = 15.3dBm
> >
> >This equation computes the (discrete) integral of the PSD, where
> >(f5mag-116) is the PSD from your code, and 60dB converts from MHz to
>Hz.
> >
> >
> >
> >-----Original Message-----
> >From: stds-802-3-10gbt@IEEE.ORG [mailto:stds-802-3-10gbt@IEEE.ORG] On
> >Behalf Of sailesh rao
> >Sent: Wednesday, July 21, 2004 3:29 PM
> >To: STDS-802-3-10GBT@listserv.ieee.org
> >Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
> >
> >Jose,
> >
> >Please point out which lines in the matlab code I distributed,
> >spectra.m, have "bugs".
> >
> >Regards,
> >Sailesh Rao.
> >srao@phyten.com
> >
> > >From: Jose Tellado <JTellado@TERANETICS.COM>
> > >Reply-To: "IEEE P802.3an" <STDS-802-3-10GBT@listserv.ieee.org>
> > >To: STDS-802-3-10GBT@listserv.ieee.org
> > >Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
> > >Date: Wed, 21 Jul 2004 12:14:42 -0700
> > >
> > >Sailesh,
> > >
> > >It appears you have a bug in your program. You are assuming that
>PAM12
> > >is transmitting 0.8dB more power than PAM8 which is unfair. When you
> > >correct for this PAM12 should have better EMI.
> > >
> > >Jose
> > >
> > >Details:
> > >
> > >When I compute the total power transmitted for the PAM8 case by
> > >integrating the PSD I get 4.1dBm
> > >
> > >10*log10(sum(10.^((f8mag-116)/10)))+60 = 4.1dBm
> > >
> > >But when I compute the total power tx for the PAM12 case I get 4.9dBm
> > >
> > >10*log10(sum(10.^((f12mag-116)/10)))+60 = 4.9dBm
> > >
> > >
> > >PS. You probably made a mistake in the Butterworth filtering sampling
> > >rate adjustment or in a amplitude/power log mix-up.
> > >
> > >
> > >-----Original Message-----
> > >From: stds-802-3-10gbt@IEEE.ORG [mailto:stds-802-3-10gbt@IEEE.ORG] On
> > >Behalf Of sailesh rao
> > >Sent: Wednesday, July 21, 2004 9:37 AM
> > >To: STDS-802-3-10GBT@LISTSERV.IEEE.ORG
> > >Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
> > >
> > >Jose,
> > >
> > >It turns out that when you take into account the analog filtering and
> > >do an accurate calculation of the PSD/"EMI PSD", neither PAM8 nor
>PAM12
> >
> > >has an advantage in terms of EMI. I'm attaching the PDF ouput and the
> > >matlab code to generate the PSDs using both Ungerboeck's analog
>filter
> > >construction (3rd order BW LPF at fs/4) and using the (0.75+0.25D)
> > >approach used in our July presentation (with 5th order BW LPF at
>fs/2).
> > >In both cases, the peaks for the so-called "EMI PSD"s are within
>0.01dB
> >
> > >of each other for PAM8 and PAM12.
> > >
> > >Regards,
> > >Sailesh Rao.
> > >srao@phyten.com
> > >
> > > >From: Jose Tellado <JTellado@TERANETICS.COM>
> > > >Reply-To: "IEEE P802.3an" <STDS-802-3-10GBT@listserv.ieee.org>
> > > >To: STDS-802-3-10GBT@listserv.ieee.org
> > > >Subject: Re: [10GBT] Request for Cat6 Emissions Characteristics
> > > >Date: Wed, 21 Jul 2004 00:06:30 -0700
> > > >
> > > >
> > > >
> > > >
> > > >All,
> > > >
> > > >From talking to several 10GBase-T EMI experts, the general
>consensus
> > > >is
> > >
> > > >that EMI emissions increase with frequency as 20*log10(f).
> > > >
> > > >Thus the system with the higher symbol rate (PAM8 at 1000MHz) will
> > > >have
> > >
> > > >worse EMI if the tx power is the same and both have equivalent
> > > >digital and analog filtering.
> > > >
> > > >The plot below shows the EMI PSD for 1GBase-T, PAM12 and PAM8
> > > >assuming all have the same digital filter 3/4+1/4D. As expected the
> > > >PAM8 is the worse, since it has the most signal at higher
> >frequencies.
> > > >
> > > >
> > > >
> > > >I only plotted the PSD up to 0.4*SymbolRate, because the analog
> > > >filters
> > >
> > > >will typically have >3dB attenuation at 0.5*Symbol rate and the PSD
> > > >is mostly dependent on the analog filters. PAM12 and PAM8 will both
> > > >have similar analog filters.
> > > >
> > > >For those interested in the details I included the matlab code. For
>a
> >
> > > >fixed tx power the PSD level (dBm/Hz) will drop as -10*log10(BW)
>when
> >
> > > >we increase the bandwidth, BW. But as we increase the BW, the EMI
> > > >increases as 20*log10(BW). Clearly the increase in EMI in PAM8 is
> > > >twice
> > >
> > > >as bad as the PSD level drop.
> > > >
> > > >Thus PAM12 has 10*log10(1000)=0.8dB more signal at low frequencies,
> > > >but
> > > >PAM8 has 1.6dB more EMI at high frequencies. Therefore PAM8 has
>0.8dB
> >
> > > >more EMI
> > > >
> > > >Jose
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >-----Original Message-----
> > > >From: stds-802-3-10gbt@IEEE.ORG [
><mailto:stds-802-3-10gbt@IEEE.ORG>
> > > >mailto:stds-802-3-10gbt@IEEE.ORG] On Behalf Of sailesh rao
> > > >Sent: Tuesday, July 20, 2004 6:55 PM
> > > >To: STDS-802-3-10GBT@listserv.ieee.org
> > > >Subject: [10GBT] Request for Cat6 Emissions Characteristics
> > > >
> > > >Hi All,
> > > >
> > > >At the request of a task force member, I computed the transmit PSD
> > > >for PAM8,
> > > >PAM12 and 1000BASE-T, and discovered that I added the contribution
>of
> >
> > > >Jose's 0.4dB incorrectly in my Total EMI Penalty calculations in
>the
> > > >updated table.
> > > >Actually, in the passband, the transmit PSD for PAM8 after THP is
> > > >1.6dB
> > >
> > > >lower than the transmit PSD for PAM12 after THP, and not 0.8dB
>lower
> > > >as
> > >
> > > >I had reported earlier.
> > > >
> > > >However, rather than simply adding another 0.8dB to the PAM12 EMI
> > > >penalty, I would like to propose that we compute the estimated
> > > >emissions characteristics of the PAM8/PAM12 transmit PSDs, for
> > > >different transmit filtering choices, over typical Cat6 cabling and
> > > >assess the difference in peaks to estimate the true emissions
>penalty
> >
> > > >for one PAM approach over the other. I know Scott Powell had
> > > >published a PDF version of measured 4-connector Cat6 emissions
> > > >characteristics for a flat transmit PSD (powell_1_0303.pdf), but do
> > > >cabling experts agree with Scott's measurements and can the task
> > > >force use that data to
> > >
> > > >assess the emissions characteristics of PAM8 vs. PAM12? If so, I
> > > >would like to request Scott to publish a file version of his
> > > >measurements on the task force web site so that we can all use it
>to
> > > >do fair comparisons. If not, are there other typical Cat6 cabling
> > > >emissions measurements that we can use to do the emissions
> >comparisons?
> > > >
> > > >Any input from the cabling experts on the reflector would be
>greatly
> > > >appreciated.
> > > >
> > > >Regards,
> > > >Sailesh Rao.
> > > >srao@phyten.com
> > > >
> > > >_________________________________________________________________
> > > >Don't just search. Find. Check out the new MSN Search!
> > > > <http://search.msn.click-url.com/go/onm00200636ave/direct/01/>
> > > >http://search.msn.click-url.com/go/onm00200636ave/direct/01/
> > > >
> > > >
> > > >
> > > ><< PSDPAM12andPAM8.m >>
> > >
> > >_________________________________________________________________
> > >Is your PC infected? Get a FREE online computer virus scan from
> > >McAfee(r) Security.
> > >http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
> >
> >_________________________________________________________________
> >Is your PC infected? Get a FREE online computer virus scan from
> >McAfee(r) Security.
> >http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
> >
>
>_________________________________________________________________
>FREE pop-up blocking with the new MSN Toolbar - get it now!
>http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
_________________________________________________________________
Planning a family vacation? Check out the MSN Family Travel guide!
http://dollar.msn.com
PSD Comparisons.pdf
spectra.m