RE: 850 nm solutions
Well, "relative cost" is the sellers "relative price", right ?
We are building most stuff from sand and organic deposits, which are
governed by local countries laws. However IEEE is an International
organization, so relative price of sand varies relative to what country
you are in. So how does this make sense to anyone, to state relative
cost/price of sand if the context is not known ? Relatively speaking,
I'm lost ...
-Curt-
PS. We are a non profit org, so to us isn't cost and price almost the same
thing!!!
-----Original Message-----
From: Geoff Thompson [mailto:gthompso@xxxxxxxxxxxxxxxxxx]
Sent: Thursday, April 20, 2000 12:52 PM
To: Jonathan Thatcher
Cc: 'McCormick, Corey'; stds-802-3-hssg@xxxxxxxx; David Law (E-mail)
Subject: RE: 850 nm solutions
Jonathan-
Even "relative pricing" isn't OK, "Relative cost" is what we are constrained
to.
"Pricing" is an artificial structure that includes profit. Therefore
discussions of pricing have nasty anti-trust implications.
You have found where the fine line is drawn.
Geoff
At 12:29 PM 4/20/00 -0700, Jonathan Thatcher wrote:
Corey,
We have pretty strict rules about sharing any kind of price information in
the IEEE. You will see in previous notes "relative pricing." This is okay.
Absolute pricing is not.
David,
Please get this note deleted off the archive.
Everyone,
Please all references to the enclosed note.
Thank you,
jonathan
Jonathan Thatcher,
Chair, IEEE 802.3ae (10 Gigabit Ethernet)
Principal Engineer, World Wide Packets
PO BOX 141719, Suite B; 12720 E. Nora, Spokane, WA 99214
509-242-9000 X228; Fax 509-242-9001; jonathan@xxxxxxxxxxxxxxxxxxxx
-----Original Message-----
From: McCormick, Corey [ mailto:Corey@xxxxxxxxx <mailto:Corey@xxxxxxxxx> ]
Sent: Thursday, April 20, 2000 8:37 AM
To: stds-802-3-hssg@xxxxxxxx
Subject: RE: 850 nm solutions
Sure thing. The 0.5M spec is for one of our vendors (proprietary Cisco
GigaStack) GBIC that uses something akin to the FireWire cable for Single
GigE or Dual GigE switch-to-switch connections in a single GBIC slot. It is
not 1000BASE-CX, but at least it is inexpensive and available for
closet/rack interconnects.
The 1000BASE-CX is supporting longer links but costs almost the same as
1000BASE-SX GBICs (lack of volume drives the cost up I suspect). However,
1000BASE-CX is extremely rare in our experience. The majority of our NIC
vendors (3Com, IBM, Compaq, Alteon), provide almost exclusively SX NICs
without the benefit of using a GBIC slot, and this has further limited our
practical choices. The cost of a 1000BASE-SX NIC with a fixed (non-GBIC
interface) is very near our cost of the SX GBIC as a stand-alone part.
Today the NIC's are ~$400-600 and the SX-GBICs are ~$250-$550. (We of
course have a few proprietary NICs @ $1000-$2000 each, but thankfully they
are the exceptions.) Even obtaining 1000BASE-CX GBICs has been tough, much
less getting them supported by another vendor's GBIC interface. GBICs can
be great, but it does not yet share the compatibility level of 10Base AUI,
or even 100Base MII in our day-to-day lives. Just because the connector
fits, doesn't mean the link works well...
I suspect that the promise of 1000Base-TX pretty much killed the 1000Base-CX
market and it's development, but with no TX standard likely for 10G (I will
trust all you in-the-trenches-EE-types for that insight), the CX option
should be much more popular I believe. To a large extent I think this will
depend on cost (again) as we obviously need both ends of the links to
support the same interface media and they are under different market
pressures I believe. Cost is always an issue, but packaging on the NIC side
is much less of a problem that on the switch side.
As market pressure/competition has brought prices down and density up for
the GigE switches, we are seeing the similar things in that market as well.
The packaging and cost issues seem to pushing our vendors towards the
small-footprint connectors which preclude the use of the much larger but
more convenient and expensive GBIC/SC connector housing. In the
standalone/pizza-box (1U-5U in height) GigE switches, GBICs are still
common, but in the Slot-based switching chassis the GBIC interface looks to
be fading. There are exceptions for dedicated uplink ports where the GBIC's
flexibility seems to be of prime importance.
If the cost differential for any copper spec 10GigE over the same fiber
solution is very large, I believe it will be very popular if the distance is
great enough to cover much of the installed data center topologies. Our
main data center is ~75M across and we use two central switching locations.
So, for us 25M will do many of our connections. (~50% I would think)
We have architected our data center clusters around other fairly short
maximum lengths such as High-Voltage Differential SCSI, Low-Voltage
Differential SCSI, IBM's SSA Serial Disk architecture, etc... so this would
be nothing unfamiliar.
Hope this helps,
-Corey
-----Original Message-----
From: Ed Grivna [ mailto:elg@xxxxxxxxxxx <mailto:elg@xxxxxxxxxxx> ]
Sent: Thursday, April 20, 2000 7:16 AM
To: stds-802-3-hssg@xxxxxxxx; McCormick, Corey
Subject: RE: 850 nm solutions
Hi Corey,
could you please clarify the statement below? Where on earth
does this half-meter length spec for 1000BASE-CX come from?
Copper GBICs should be good for from 5 to 20 meters at
gigabit rates.
Regards,
Ed Grivna
> Speaking as a customer, we would likely make use of almost
> as many 10M links as those > 10M. We currently use GigE
> links for both servers (1500 MTU and Jumbo) and as connections
> for distribution switches. We find the 0.5M Copper GBIC's less
> than useful, but about 35% of our links are <=10M. A low-cost
> 10-25M Coax would be quite useful as most of our connections in
> the data centers can utilize this length. The three predominant
> uses for our 1G connections today are spread fairly evenly
> about 1/3rd each:
>
>
> Corey McCormick
> CITGO Petroleum
> corey@xxxxxxxxx
>