RE: 3PMD Proposal
Bernd,
As I understand it, you have to use the patch cord to achieve the currently
quoted distances in the 1310 solutions over multimode fiber. The switch
vendors can only guarantee a distance that is supported by the standard. I
agree that 90% of fibers out there have greated bandwidth than those quoted
in the standard. If we could use this reasoning, the 850nm CWDM could go
250 - 300m on installed base. But since we have to use the 160MHz . Km
fiber, we get 100m. Similarly, 1310WWDM only has 500MHz.km and therefore
only goes about 300m. You do not get 500MHz.km bandwidths without the fiber
patch cord (worst case design).
Eric Grann
Chief Technical Officer
Blaze Network Products
-----Original Message-----
From: owner-stds-802-3-hssg@xxxxxxxx
[mailto:owner-stds-802-3-hssg@xxxxxxxx]On Behalf Of
Bernd.Prediger@xxxxxxxxxxxx
Sent: Thursday, June 15, 2000 3:31 AM
To: david_cunningham@xxxxxxxxxxx; stds-802-3-hssg@xxxxxxxx
Subject: AW: 3PMD Proposal
David,
"min. overfilled launch" as in the Ottawa presentation from Del may imply
the use of a patch cord. At least myself (and maybe others) missed it.
Anyway, a patch cord is a solution that guarentees greater distance over old
fiber and that's good.
For our 5 distance objectives this could mean that a serial 1300nm solution
fulfills them all probably long term at lower cost then a CWDM just by
adding a patch cord were necessary.
In this matter I agree with Ed Cornejo that most (90%+) of the LX GBE
applications today work without patch cord. We tested serial 10 Gig on
random fiber over 500m without any problem!
Best wishes
Bernd
-----Ursprüngliche Nachricht-----
Von: david_cunningham@xxxxxxxxxxx [mailto:david_cunningham@xxxxxxxxxxx]
Gesendet am: Dienstag, 13. Juni 2000 23:45
An: stds-802-3-hssg@xxxxxxxx
Betreff: FW: 3PMD Proposal
-----Original Message-----
From: CUNNINGHAM,DAVID (A-SanJose,ex1)
Sent: Tuesday, June 13, 2000 10:27 AM
To: 'Larry Miller'
Cc: 'Stds-802-3-Hssg@xxxxxxxx'
Subject: RE: 3PMD Proposal
Larry,
as far as I know it has always been stated that the offset launch
patchcord was part of the WWDM proposal, so there should be no surprises
there.
Regarding: "The offset patchcord has been terribly unpopular with us"
For 1 Gigabit Ethernet this may be your and your companies position.
However, it must be remembered that from a technical point of view
1000BASE-LX with the offset launch patchcord is the ONLY way to robustly (in
a worst case sense) go beyond 300 m on installed 160/500 and 200/500
multimode fiber (not the new multimode fiber types with RML specifications).
It is true that 1000BASE-SX links typically go further than 300 m - but this
is by no means guaranteed.
Regarding: "adding so much cost that it nearly doubles the cost of 1 Gb MM
LX links."
If customers want to use installed links with lengths of up to at least 550m
whilst avoiding the much larger cost of installing new multimode fiber -
then the offset launch patchcord makes very good economic sense. I know
that some equipment suppliers suggest their customers use 1000BASE-LX with
the patchcords for such cases.
Regarding: "Is the Agilent 4X WWDM going to work with SMF? I will be wanting
to know that...."
The WWDM proposal to the IEEE 802.3ae is for a PMD that is capable of
operating on either SMF or MMF - just like 1000BASE-LX does. That it is will
be mandatory that is the WWDM PMD is dual use for SMF and MMF.
Best wishes,
David.
-----Original Message-----
From: Larry Miller [ mailto:ldmiller@xxxxxxxxxxxxxxxxxx
<mailto:ldmiller@xxxxxxxxxxxxxxxxxx> ]
Sent: Tuesday, June 13, 2000 6:59 AM
To: david_cunningham@xxxxxxxxxxx <mailto:david_cunningham@xxxxxxxxxxx> ;
Bernd.Prediger@xxxxxxxxxxxx; piers_dawe@xxxxxxxxxxx
Cc: Stds-802-3-Hssg@xxxxxxxx <mailto:Stds-802-3-Hssg@xxxxxxxx>
Subject: RE: 3PMD Proposal
Arghhhh!!! Are we really back to that, David? The offset patchcord has been
terribly unpopular with us, adding so much cost that it nearly doubles the
cost of 1 Gb MM LX links.
Is the Agilent 4X WWDM going to work with SMF? I will be wanting to know
that.....
Larry Miller
-----Original Message-----
From: david_cunningham@xxxxxxxxxxx [SMTP:david_cunningham@xxxxxxxxxxx]
Sent: Monday, June 12, 2000 9:04 PM
To: Bernd.Prediger@xxxxxxxxxxxx; piers_dawe@xxxxxxxxxxx
Cc: Stds-802-3-Hssg@xxxxxxxx
Subject: RE: 3PMD Proposal
Bernd,
the offset launch patchcord is assumed for the 1300 nm WWDM case for
10 Gigabit Ethernet. As was documented in IEEE 802.3z 1000BASE-LX the
offset launch patchcord ensures a worst-case minimum bandwidth of 500
MHz.km. For 1300 nm links the inclusion of the offset launch patchcord
obsoleted the 385 Mhz.km modal bandwidth value that was present in some
older drafts of the 1000BASE-LX clause.
In conclusion, since the offset launch patchcord is part of the 1300
nm WWDM
proposal 500 MHz.km is the correct modal bandwidth to use for the multimode
links.
Best wishes,
David.
-----Original Message-----
From: Bernd.Prediger@xxxxxxxxxxxx [ mailto:Bernd.Prediger@xxxxxxxxxxxx
<mailto:Bernd.Prediger@xxxxxxxxxxxx> ]
Sent: Wednesday, June 07, 2000 9:49 AM
To: piers_dawe@xxxxxxxxxxx
Cc: Stds-802-3-Hssg@xxxxxxxx
Subject: 3PMD Proposal
Hello Piers,
I just got through Del's presentation from Ottawa again and stumpled over
your calculation for the "Minimum Range" of CWDM over installed MM-Fiber
(Slide 4).
You calculated 2-300m for all 500MHz*km fiber but I understood that since
Gigabit Ethernet the worst case effective bandwidth everbody agreed on is
375MHz*km. Our calculation with the latter value let to about 180m.
What am I missing here? (Of course we used your spreadsheet!)
Best wishes
Bernd