RE: Optical Connectors
For a telecom service provider, the use of LC connectors recommended for
10GbE transceivers will not affect whether they recommend SC connectors for
their networks since the service providers typically connect to the
equipment via Fiber trays which adapt whichever connector (SC, ST, APC,...)
may be present on the equipment faceplate. This year, several equipment
vendors have shown deployed equipment with MU, LC, and other -- even
proprietary connector types on certain ultra-long haul equipment in multiple
networks in Metro, Long haul, submarine applications. Most service
providers continue to specify SC for connection to their fiber plant which
is accomplished via fiber trays.
I do not believe that adoption of LC connector by IEEE precludes the
(continued) use of SC connector by any network/service provider and moves us
in the right direction for SFFs @ 10G.
-rohit
Rohit Sharma
>
> Chris,
>
> I am not sure of your comment about LC having a proven track
> record for
> single mode implementations. At present, WorldCom has not
> deployed any
> LC. All of the connectors currently specified for SM
> installations is
> SC. A particular vendor is attempting to get WorldCom to
> make use of their
> connectors. ( I will not say how successful or not they are.
> ) Several
> system vendors are attempting to make use of LC, but at
> present, none have
> been certified. Given the form factor that would use XAUI,
> SFF connectors
> would not be a requirement.
>
> Thank you,
> Roy Bynum
>
>
> At 04:28 PM 7/21/00 -0600, Chris Simoneaux wrote:
>
> >Our opinion is that LC is a better connector than MTRJ. The
> LC does not
> >seem to suffer the possible damage that MTRJ can see with
> high mate/demate
> >cycles...due to the guide pin action. Also, the LC has a
> proven track
> >record for singlemode whereas the MTRJ does not.
> >
> >PS: My feeling is the standards body's charter should be to specify a
> >connector. However, there's too much rhetoric in the
> procedure. Therefore
> >it's difficult to choose the best solution. Inevitably the
> real winner/s
> >will come forward. Conclusion: Choose a connector at the
> standards level as
> >it can expose good points of each solution.
> >
> >Chris Simoneaux
> >Picolight
> >
> >-----Original Message-----
> >From: Roy Bynum [mailto:rabynum@xxxxxxxxxxxxxx]
> >Sent: Tuesday, July 18, 2000 12:09 PM
> >To: Jonathan Thatcher; HSSG_reflector (E-mail)
> >Subject: Re: Optical Connectors
> >
> >
> >
> >Jonathan,
> >
> >In spite of what Lucent wants, the LC connector does not
> have the market
> >support that MTRJ does. MTRJ also has a smaller form factor
> than does
> >LC. I don't like and am specifying the non-use of LC on
> transmission gear
> >because of the fragile "lock" tab that is on the connector.
> >
> >Thank you,
> >Roy Bynum
> >
> >
> >At 08:48 AM 7/18/00 -0700, Jonathan Thatcher wrote:
> > >I have opened this thread to continue the discussion on optical
> > >connectors. So far (what has come into my reader), we have
> the following
> > >comments:
> > >
> > >-----------------------
> > >"Bill Wiedemann: Regarding 850CWDM we are planning to make first
> > >implementations with duplex SC moving to LC with small
> form factors. Our
> > >expectation is that small form factor with LC could be
> available a year
> > >from today. "
> > >-----------------------
> > >"Jim Tatum: I would assume that 802.3ae would do the same
> as 802.3z, and
> > >NOT specify conectors. "
> > >-----------------------
> > >"Ed Chang: There are so many different form factors, and
> connectors, which
> > >even the GbE and Fibre Channel market can not get consensus."
> > >-----------------------
> > >
> > >If we review the 802.3 Ethernet specification, we see that we have
> > >identified connectors for each variant (I don't remember
> an exception).
> > >For example:
> > >7.6.2 AUI Configuration cable
> > >9.9.5.2 Optical for repeaters
> > >...
> > >38.11.3 MDI = Duplex SC for GigE Optics
> > >39.5.1 MDI = Style 1 (DB9) and Style 2 for GigE Cu
> > >
> > >While I remember no rules that require us to do so, it
> seems obvious that
> > >there exists a precedent which should guide our decision.
> > >
> > >In 802.3z, we specifically took a vote to avoid connector
> discussions
> > >("connector wars")**. We could do the same in 802.3ae. If
> we did, I would
> > >argue that we would, effectively, be retaining the duplex
> SC optical
> > >connector specified in clause 38.
> > >
> > >My PERSONAL preference would be to specify the LC
> connector. Rationale:
> > >1. There seems to be an overall inclination to move in
> that direction.
> > >2. It sets the stage for some kind of "Small Form Factor" 10 Gig
> >transceiver.
> > >3. I don't think that it would negatively impact the cost of the
> > >transceiver in the 2002 (standard completion time frame).
> > >
> > >As CHAIR, I don't want to use up any cycles on this. If there isn't
> > >sufficient consensus to agree on an alternative to the SC,
> we should just
> > >adopt the SC and move on.
> > >
> > >jonathan
> > >
> > >** In reality, this was bumped up to 802.3 because neither
> I (sub-chair
> > >for PMD) nor Howard (802.3z chair) wanted to use precious
> committee time
> > >for the discussion.
> > >
> > >Jonathan Thatcher,
> > >Chair, IEEE 802.3ae (10 Gigabit Ethernet)
> > >Principal Engineer, World Wide Packets
> > >PO BOX 141719, Suite B; 12720 E. Nora, Spokane, WA 99214
> > >509-242-9000 X228; Fax 509-242-9001; jonathan@xxxxxxxxxxxxxxxxxxxx
> > >
>