RE: Short haul PMDs
According to Dell'Oro's numbers, about 8,000 1000Base-T networking ports
shipped in Q1/00. The Q2/00 numbers should be out soon.
Regards,
Marshall
408.586.1754 direct
408.586.1900 fax
408.398.0014 cell
-----Original Message-----
From: owner-stds-802-3-hssg@xxxxxxxx
[mailto:owner-stds-802-3-hssg@xxxxxxxx]On Behalf Of Seto, Koichiro
Sent: Thursday, August 03, 2000 4:58 PM
To: pat_thaler@xxxxxxxxxxx; gthompso@xxxxxxxxxxxxxxxxxx; hakimi@xxxxxxxxxx
Cc: stds-802-3-hssg@xxxxxxxx
Subject: Re: Short haul PMDs
[Date: 08/03/2000 From Seto]
Maybe, HP pro-curve unit has... They are the one of a few vendors actually
shipping 1000BASE-CX options I believe.
Seto
>
> So, does anyone have data on what percentage of Gigabit Ethernet links
> ship with 1000BASE-CX?
>
> Pat
>
> -----Original Message-----
> From: Geoff Thompson [mailto:gthompso@xxxxxxxxxxxxxxxxxx]
> Sent: Wednesday, August 02, 2000 4:45 PM
> To: Hakimi, Sharam (Sharam)
> Cc: stds-802-3-hssg
> Subject: RE: Short haul PMDs
>
>
>
> Sharam-
> I think 15 years is a slight exaggeration. 10BASE-T started as a Study
> Group in August of 1987. It was the first group to have a 100 meter
> objective.
>
> Before 10BASE-T there was the following:
> 10BASE5 + AUI The AUI cable was 50 meters max
> 10BASE2 The coax was daisy-chained w/ an overall max of 185m
> 1BASE5 (StarLAN) The hub to DTE distance was 250 m
> 10BROAD36 Broadband diameter of 2800 meters
> FOIRL 1000 meter links
> The point here is that topology has evolved as well as speed.
> We have in the recent past had a distance objective for short cables in
> 802.3z (ref: 1000BASE-CX).
>
> The 100 meter distance history is rooted in facilities cabling and is
based
> on the (literally) cast-in-concrete distance of 90 m max from the cabling
> closet to the telecommunications outlet.
>
> If the prime market for an Ethernet project is not oriented to
> "in-the-wall" cabling then the 100 meter distance is not sacrosanct. The
> objective for 100 meters as approved in York was for "installed" cabling
> from ISO/IEC 11801. That means that we were talking about generic
> facilities cabling at the time, not application specific cabling.
>
> If we do go to application specific cabling then we have to do the
> specification in our own standard instead of referencing an outside
cabling
> standard such as ISO/IEC 11801.
>
> Geoff
>
>
> At 11:16 AM 8/2/00 -0400, Hakimi, Sharam (Sharam) wrote:
>
> >During the past 15 years and through all of 802.3 distance Objectives,
100
> >meters has been the minimum and essentially the trademark of IEEE 802.3.
> >There has always been discussions that if the distance is reduced we can
> >provide less expensive PHYs, but the cost difference never justified
> >development of these PHYs . Providing 100 meter solutions does not
prevent
> >anyone from using a 10, 20, 30 or other length cables as their needs
> >require. However, if time has come that the cost difference between a 100
> >meter solution and something less will justify such development then we
> >could look at it later, but changing the objectives at this time is a BAD
> >idea in my opinion.
> >
> >Sharam Hakimi
>