Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

[802.3_GEPOF] Fwd: [802.3_DIALOG] Unresolved comments on P802.3bv


— Rubén Pérez-Aranda

Inicio del mensaje reenviado:

De: Rubén Pérez-Aranda <rubenpda@xxxxxxxxx>
Asunto: Re: [802.3_DIALOG] Unresolved comments on P802.3bv
Fecha: 29 de agosto de 2016, 21:07:08 CEST
Para: Rubén Israel Pérez de Aranda Alonso <rubenpda@xxxxxxxxx>

Dear Colleagues,

As we agreed in the 802.3 Plenary Meeting of July, a presentation has been posted to 
where I provide measurement results that validate the transmission distortion parameters
as requested by the comment #118 against P802.3bv/D2.0. 

The presentation also provides an small tutorial on the script specified in the draft to compute the
distortion parameters based on the signal captured in TP2, when the PMA is configured by MDIO
to generate test mode 6. I hope that this small tutorial helps you to understand the rational 
of the signal processing that the script implements to calculate the transmitter distortion parameters.

I will present these measurement results in Sept Interim Meeting in the 802.3bv TF. Any comment or 
question that may help to improve the presentation and get the comment solved is very welcome.

Thank you and best regards,

Rubén Pérez-Aranda
KDPOF CTO
P802.3bv Comment Editor, Editor

El 28 jul 2016, a las 23:12, Rubén Pérez-Aranda <rubenpda@xxxxxxxxx> escribió:

Dear Peter,

thank you to open the thread on this topic. Regarding to your two key points, I would like to put the attention 
of the group on two presentations:

  • http://www.ieee802.org/3/bv/public/Jan_2016/takahashi_3bv_03a_0116.pdf:
    • This presentation contains the measurements of transfer functions carried out for several different SI-POF that meet IEC 60793-2-40 sub-category A4a.2.
    • Based on those measurements, the lower bound limit for the spec have been developed.
    • As it is stated in sub-clause 114-7: "1000BASE-RHx operation requires fiber optic cable meeting the requirements of IEC 60793-2-40 subcategory A4a.2 multimode plastic optical fibers with appropriate augmentation as specified in this sub-clause”. This is because 1000BASE-RHx specifies the modal power distribution (MPD) of PMD TX in spec point TP2 and there is not international Std. that specifies the insertion loss and the transfer function for that MPD.
    • The specification/control of the MPD is necessary in TP2 to guarantee a minimum bandwidth of the channel and a maximum insertion loss by modal dispersion.
    • The P802.3bv TF have measured the most representative POF fibers of the market (>98% of market share). Is it enough to create an standard?
    • Subclauses 114.7.4 and 114.7.5 provide references to international standards on methodologies to measure the insertion loss and transfer function. The P802.3bv TF thinks that response and insertion loss specs have to be guaranteed by the POF manufacturer and the MPD of TP2 per EAF by the PHY implementor. Is the end user of the technology to measure the transfer function of the POF in his home? Do really that for Cat 5 cables? 

The 802.3bv TF is very open to work with you (Peter and Pete) to improve the draft receiving from you specific feedback for doing that.

Kind regards,

Rubén
_____________________________________
Rubén Pérez-Aranda
CTO
KDPOF - Knowledge Development for POF
http://www.kdpof.com
_____________________________________

El 28 jul 2016, a las 13:23, Peter Stassar <Peter.Stassar@xxxxxxxxxx> escribió:

Dear 802.3 colleagues,
 
FYI.
I initially sent it to the wrong reflector.
 
Kind regards, also on behalf of Pete Anslow
 
Peter
 
From: Peter Stassar 
Sent: Thursday, July 28, 2016 10:16 PM
To: STDS-802-3-GEPOF@xxxxxxxxxxxxxxxxx
Cc: 'STDS-802-3@xxxxxxxxxxxxxxxxx'; 'Pete Anslow'; Law, David
Subject: Unresolved comments on P802.3bv 
 
Dear bv-participants,
 
This email is intended to provide some further exposure to several unresolved comments on optical subclauses in IEEE 802.3bv, especially because of the intent of bv to request the 802.3WG for approval at today’s Closing Plenary to go for Sponsor Ballot from the San Diego meeting.
 
This email is written on my behalf and of Pete Anslow, with whom I share similar concerns.
 
There are unresolved comments to bv regarding what we feel is an insufficiently validated optical specification to ensure multi-vendor compatibility.
This is especially important because of the claimed application for home users.
We strongly feel that home users should be protected by an extremely robust specification.
 
Our comments specifically addressed the need to validate the optical interface specification by testing, showing that devices meeting the specification would work in the application and that devices not meeting the specification would not work in the application.
As far as we are aware this testing has not been done and only simulation results have been presented which we feel are an inadequate validation of the specification.
 
Additionally, while the draft standard calls out a particular optical fiber specification not all fibers compliant to this specification will operate satisfactorily so the draft standard contains additional requirements, which are not realistically measurable by consumer end users.
 
Kind regards, also on behalf of Pete Anslow,
 
Peter
 
Peter Stassar, 施笪安
Technical Director, 技术总监
Huawei Technologies Ltd, 华为技术有限公司
European Research Center, 欧洲研究所
Karspeldreef 4, 1101CJ Amsterdam
The Netherlands
Tel: +31 20 4300 832
Mob: +31 6 21146286