Re: [802.3_EPOC] Why multiple simultaneous MCS
Duane,
Since we're nit-picking - not MAC, but MAC Control and not PHY aware, but
PHY speed aware. For that, MAC Control does not need to know how many
subcarriers are used, or what the bit loading on each subcarrier is. All you
care about is the number of bits per second the MAC can effectively push
through the PHY. Anything else should be left for PHY to figure out, without
involvement of MAC.
Marek
From: Duane Remein [mailto:Duane.Remein@xxxxxxxxxx]
Sent: Wednesday, October 10, 2012 15:42
To: STDS-802-3-EPOC@xxxxxxxxxxxxxxxxx
Subject: Re: [802.3_EPOC] Why multiple simultaneous MCS
Eugene,
Unless the PHY will be running at 1 Gbps over GMII or 10G over XGMII then
yes, the MAC will need to be "PHY aware". I thought that fact was already
established.
Best Regards,
Duane
FutureWei Technologies Inc.
duane.remein@xxxxxxxxxx
Director, Access R&D
919 418 4741
Raleigh, NC
From: Dai, Eugene (CCI-Atlanta) [mailto:Eugene.Dai@xxxxxxx]
Sent: Wednesday, October 10, 2012 3:29 PM
To: STDS-802-3-EPOC@xxxxxxxxxxxxxxxxx
Subject: Re: [802.3_EPOC] Why multiple simultaneous MCS
In order to achieve multiple downstream MCS for EPOC we need so called "PHY
aware MAC"; it could be done but I am afraid it will deviate from EPON MAC
too much to preserve the backward compatibility.
Eugene Dai PhD
Principle Transport Architect
COX Communications
Tel: 404-269-8014
From: Marek Hajduczenia [mailto:marek.hajduczenia@xxxxxx]
Sent: Wednesday, October 10, 2012 3:01 PM
To: STDS-802-3-EPOC@xxxxxxxxxxxxxxxxx
Subject: Re: [802.3_EPOC] Why multiple simultaneous MCS
Matt,
It would be nice if the discussion also involved these "others" you
reference. It seems that you're building a case for pre-existing consensus
on this topic, yet this is not what we observed at the last meeting in
Geneva. I would encourage these "others" to voice their opinions rather than
rely on the group representation.
Now, for technicalities.
Your argument on SNR headroom is valid enough for consideration. However,
the way we have typically designed specs before was on putting also some
requirements on the cable plant and not only on the equipment. It seems to
me that you're building the case under which the cableplant can be as bad or
good as it is, while the equipment has to have all the required flexibility
to adapt to any plant (physical link) that it has to operate on (and
conversely, take the hit in terms of complexity and resulting cost). While
it is fine if that is what the group wants, before we take the plunge into
development, I think it would be worthwhile if yourself and the unnamed
"others" presented a detailed analysis of the added cost, impact on latency
and something more of a detailed study of how such MCS function could be
implemented in EPoC without moving away from EPON-like protocol. I
understand that there may be growing consensus on the side of DOCSIS 3.1
that it needs to be done, but without such a study, I personally will not be
able to make an educated vote on this matter. Seeing how you propose this to
be done in 802.3 architecture would make all the difference for me.
I voiced my concerns before and I hope solution exists to them in a way that
makes us move forward. Appealing as the MCS might be, it needs to go through
the proper technical scrutiny, involving looking at the cost / performance /
latency / implementation issues. Only then I believe we can take a decision,
and not before.
Regards
Marek
From: Matthew Schmitt [mailto:m.schmitt@xxxxxxxxxxxxx]
Sent: Tuesday, October 09, 2012 23:25
To: STDS-802-3-EPOC@xxxxxxxxxxxxxxxxx
Subject: [802.3_EPOC] Why multiple simultaneous MCS
Based on some of the discussions, I think it might be worthwhile to spend a
moment going into the chain of reasoning that led myself (and others) to the
conclusion that an advanced next generation HSD system for HFC (such as
EPoC) should include the ability to support multiple simultaneous Modulation
and Coding Schemes (MCS).
If I were to sum it up in 2 words (okay, technically 4), it would be this:
SNR Headroom.
In a system that requires all end stations to operate with the same MCS (and
to receive all downstream transmissions), the great danger is that for
whatever reason the SNR to a given end station will change sufficiently that
it will drop offline. That simply cannot be allowed to happen. As a
result, operators are required to maintain a significant amount of "SNR
Headroom" when they setup and deploy an end station. Common practice is to
allow on order of 8 db of SNR headroom when deploying a modem (some a little
more, but I'm not aware of any that do less).
What this means is the following. Let's say that you needed 25 dB of SNR to
operate 1024 QAM with a 3/4 LDPC FEC code (which I believe is the case with
DVB-C2, and serves as a useful reference point here). An MSO would not
actually use that MCS unless they could get their end stations at 33 dB of
SNR (25+8) when deploying them. If they couldn't get to that level when
deploying the end station, they wouldn't be able to use that MCS.
I pulled out that particular number because, based on the SNR distributions
that were shared previously, even if you assumed you could "bring up" the
bottom 2.1% of modems, that's the best you could expect to do. And even if
you could further improve SNR, you're still always going to be operating in
effect 8 dB below what you could theoretically do. For example, just to get
to 4096 QAM with a 5/6 LDPC FEC, you'd need to get every single end station
to operate at about 40dB or higher of SNR.
Now, if you could get away from requiring that 8 dB of headroom, it would be
huge, considering that 6 dB is an order of modulation with the same FEC, an
increase of 2 bits per symbol.
One way to achieve that end is to support multiple MCSs, but only one at a
time, which is set based on the "lowest common denominator". In this
approach, if an end station were to have a sudden drop in SNR, then the
system would need to drop to a lower "lowest common denominator", until such
time as the problem could be addressed. By having that fall back, you could
in theory operate closer to the theoretical maximum and reduce the amount of
headroom required.
However, there are some issues here. First, one bad end station coming onto
the network - or a single problem in a single household - would affect the
entire network, degrading the service of every single end station. Second,
particularly in the scenario where an end station encounters a problem after
it's already online, there's no guarantee that it would even still be able
to communicate that it was having a problem and that it needed the MCS to be
changed. That risk is then going to force you to leave more headroom,
mitigating any potential gains.
The only approach that we've come up with so far that allows you to
significantly reduce that headroom and operate close to theoretical levels -
while not adversely affecting the entire system when there's a problem - is
to create a system in which a single end station is able to fall back to a
more robust MCS if it encounters a problem. In that way, only the single
device having an issue is affected, and unless the problem is truly
catastrophic you can reliably keep the mode online (meaning that you have an
opportunity to fix the problem while the customer remains online and
operational).
We could argue back and forth for quite a while about SNR spreads on the
network, how much variation there will be between end stations in a given
service group, etc. And the ability to operate each device to its maximum
potential is very appealing to be sure. But what really makes this
decision, in my opinion, is the SNR headroom issue, and in particular the
ability to significantly reduce it while actually improving robustness and
the ability to keep customers on line.
Thanks.
Matt
_____
_____
<="" p="">
_____
<="" p="">
_____
<="" p="">
________________________________________________________________________
To unsubscribe from the STDS-802-3-EPOC list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-EPOC&A=1