Thread Links Date Links
Thread Prev Thread Next Thread Index Date Prev Date Next Date Index

Re: ONLY one ref multiplier?: PMA clock reference





As a guy who work with Stuart and others on these issues ...I double the "Right
On, Brother!"
-joel
-------------
Fred Weniger wrote:

> Stuart,
>
> As a SerDes vendor, I can only say "Right On, Brother!"
>
>   At 08:57 AM 6/20/00 -0400, Stuart Brorson wrote:
>
> >Please allow me to make a quick comment about 155 vs. 622 MHz clocks here.
> >I was involved in OC-192 IO card design at my former employer, Nexabit
> >Networks (now Lucent Technologies), and have had some experience in this
> >department.
> >
> >It is not my desire to disparage the fine products of Giga here, so please
> >accept my apologies in advance.  However, the 10 Gig SERDES products from
> >Giga (i.e. GD16555 and GD16554) had jitter gen problems, even on the
> >company-supplied test board.  Amongst other problems, Giga's test board
> >incorporated a 155 MHz clock.  Designing a low jitter PLL/SERDES chain is
> >not very easy.
> >
> >It is noteworthy that the OIF has speced a 622 MHz reference clock freq for
> >the 10 Gig framer/SERDES.  That means that clueful PLL vendors have every
> >reason to design low-jitter 622 MHz clock modules which can be used -- or
> >modified for use -- with 10GigE also.
> >
> >In any event, most vendors with whom I am aware -- including Giga -- allow
> >the user to select either a 155 or a 622 MHz reference clock.  This allows
> >the board designer freedom to choose the design problem he wants to tackle:
> >either a lower speed 155 MHz PLL with stringent jitter specs (and a very low
> >jitter SERDES), or a higher speed 622 MHz PLL with all the intricacies of RF
> >design, but perhaps with an easier jitter (i.e. board noise) problem.
> >
> >Why not allow two clock frequencies and leave the board designer the freedom
> >of choice?
> >
> >
> >Stuart Brorson
> >Axiowave Networks
> >Marlborough, MA 01752
> >
> >
> >-----Original Message-----
> >From: Lysdal, Henning [mailto:henning.lysdal@xxxxxxxxx]
> >Sent: Tuesday, June 20, 2000 5:17 AM
> >To: 'Jscquake@xxxxxxx'; rtaborek@xxxxxxxxxxx; stds-802-3-hssg@xxxxxxxx
> >Subject: RE: ONLY one ref multiplier?: PMA clock reference
> >
> >
> >
> >Justin,
> >
> >In answer to your question:
> >
> >My company (formerly Giga) has been shipping OC-192 SerDes since 1997 and
> >the majority of our customers use 155.52 MHz reference clock.
> >
> >Regards,
> >
> >Henning
> >
> >
> >-----Original Message-----
> >From: Jscquake@xxxxxxx [mailto:Jscquake@xxxxxxx]
> >Sent: 20. juni 2000 00:18
> >To: rtaborek@xxxxxxxxxxx; stds-802-3-hssg@xxxxxxxx
> >Subject: ONLY one ref multiplier?: PMA clock reference
> >
> >
> >
> >
> >Hello Rich,
> >
> >Your proposal sounds good,i.e. to have only a single clock multiple
> >(1/4 division) for the reference clock, but I am not sure if this is wise.
> >Using
> >a lower rate frequency clock autmatically implies worse jitter performance
> >for
> >the PLL's. This is not as much of an issue for the WDM case as it is for
> >serial
> >but every psec (or even sub-ps) counts for the serial versions. So I would
> >opt
> >to be NOT too restrictive in saying only 155-156Mhz xtal osc are allowed.
> >Note that the present community of OC192 people use the higher clock rate
> >for the reference. Are there any that uses the 155MHz as a reference for
> >OC192? Having said all this ... are there readily available
> >644.53125MHz xtal osc.?
> >
> >Justin
> >
> >In a message dated 6/16/00 1:03:26 AM Pacific Daylight Time,
> >rtaborek@xxxxxxxxxxxxx writes:
> >
> > > Henning,
> > >
> > >  Sorry about the confusion. I did mention in my note that there would have
> >
> >to
> > > be
> > >  two optional clock references specified in the XBI, one for the LAN PHY
> >and
> > > the
> > >  other for the WAN PHY.
> > >
> > >  What I should have said is that only one clock MULTIPLE be specified. For
> > >  example, 161.1328125 MHz is 1/4 of 644.53125 MHz and 155.52 MHz is 1/4 of
> >
> > > 622.08
> > >  MHz. One fourth is a good multiple to use. This means that other
> >multiples
> > >  should not be required anywhere in the standard, even optionally (i.e.
> >1/8,
> > > 1/2,
> > >  1/16, 1/1, etc.)
> > >
> > >  Best Regards,
> > >  Rich
> > >
> > >  --
> > >
> > >  "Lysdal, Henning" wrote:
> > >  >
> > >  > Rich,
> > >  >
> > >  > I don't see how you can avoid having separate reference clocks for LAN
> >and
> > >  > WAN (with realistic PLL design).
> > >  >
> > >  > In the LAN case there are several options
> > >  > 156.25 MHz (seems to be prefered among serial folks)
> > >  > 161.1328125 MHz
> > >  > 644.53125 MHz
> > >  >
> > >  > In the WAN case the OIF specifies 622.08 MHz. I know of a lot of people
> >
> > > who
> > >  > also like 155.52 MHz
> > >  >
> > >  > Now the problem is: how do you synthesize 9.95328 GHz and 10.3125 GHz
> >from
> > >  > the same reference. If you use a 10 kHz reference, it's easy, but you
> >will
> > >  > most likely have problems with transmit jitter.
> > >  >
> > >  > So I haven't been discussing the WAN case at all, since I was under the
> > >  > impression that WAN PHYs will use existing SONET SerDes using 622.08
> >MHz
> > >  > refck.
> > >  >
> > >  > Regards,
> > >  >
> > >  > Henning
> > >  >
>
> Fred Weniger
> Gigabit Product Marketing Manager
> 805-388-7571
> fax: 805-384-5065
> weniger@xxxxxxxxxxx
> VITESSE
> SEMICONDUCTOR CORPORATION

--
Joel Goergen
Force10 Networks
1440 McCarthy blvd
Milpitas, Ca, 95035

Email:  joel@xxxxxxxxxxxxxxxxxxx
Direct: (408) 571-3694
Cell:  (612) 670-5930
Fax:   (408) 571-3550