Dear François and all
I have few questions:
- Why do you use TCTL instead of ELTCTL? For me scaling is not only related to IL, therefore a 100m measurement for the short link
case would be more accurate.
- RL looks for me too good, at least after installation we cannot expect such values.
Best regards
Von: Francois Beauregard <00002cfd85cd2c3d-dmarc-request@xxxxxxxxxxxxxxxxx>
Gesendet: Dienstag, 5. März 2024 17:37
An: STDS-802-3-SPEP2P@xxxxxxxxxxxxxxxxx
Betreff: Re: [802.3_SPEP2P] S parameter for 500m channel
Hello Georges,
These are a new set of S-parameters for 18AWG-500m cable; the phase issue has been corrected by doing interpolation above 32Mhz.
Sdd, Scd, Sdc : S2p touchtone formatted, 125kHz to 100 MHz, step 125kHz
SPE100 : excel format Sdd11, Sdd22, Sdd21, Scd11, Scd22, Scd21, 125kHz to 100MHz, step 125kHz
Regards
Francois Beauregard
From: George Zimmerman <george@xxxxxxxxxxxxxxxxxxxx>
Sent: Tuesday, February 27, 2024 5:22 PM
To: STDS-802-3-SPEP2P@xxxxxxxxxxxxxxxxx
Subject: [EXTERNAL] Re: [802.3_SPEP2P] S parameter for 500m channel
External Message:Use caution before opening links or attachments
Francios – did you compare the phase response? That was what tingting mentioned in her email. Sometimes phase responses (particularly at low frequencies) get messed up due to various
processing techniques. These are important for extracting time-domain simulations. They also are a bit tricky to scale properly with length.
From:
stds-802-3-spep2p@xxxxxxxxxxxxxxxxx <stds-802-3-spep2p@xxxxxxxxxxxxxxxxx>
On Behalf Of Francois Beauregard
Sent: Tuesday, February 27, 2024 2:06 PM
To: zhangtingting (O) <zhangtingting59@xxxxxxxxxx>;
STDS-802-3-SPEP2P@xxxxxxxxxxxxxxxxx
Subject: RE: S parameter for 500m channel
Hello Tingting,
I scaled down the 500m measurements to 100m. The IL was found to be in good agreement with the model proposed by Voss/Wachtel
Regards
Francois Beauregard
From: zhangtingting (O) <00001e92abc91102-dmarc-request@xxxxxxxxxxxxxxxxx>
Sent: Monday, February 19, 2024 8:46 PM
To: STDS-802-3-SPEP2P@xxxxxxxxxxxxxxxxx
Subject: [EXTERNAL] [802.3_SPEP2P] S parameter for 500m channel
External Message:Use caution before opening links or attachments
Hi,
I found that the phase calculated from the real and imag of S21 in the online Excel seems to weird. Besides, the frequency step is
0.125MHz for frequencies less than 32MHz, and increases to 0.25MHz after 32MHz. If the correct measurement data of 500m channel is not available, LT Spice model has to be used to get S parameters for time domain simulation.
The online presentation associated with the LT Spice model is wrong (incorrect link). Do the inline connectors need to be included
for the 500m channel, or just cascade five 100m segments?
Thanks
Best wishes,
Tingting
To unsubscribe from the STDS-802-3-SPEP2P list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-SPEP2P&A=1
DISCLAIMER:
Privileged and/or Confidential information may be contained in this message. If you are not the addressee of this message, you may not copy, use or deliver this message to anyone. In such event, you should destroy the message and kindly notify the sender by
reply e-mail. It is understood that opinions or conclusions that do not relate to the official business of the company are neither given nor endorsed by the company. Thank You.
To unsubscribe from the STDS-802-3-SPEP2P list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-SPEP2P&A=1
To unsubscribe from the STDS-802-3-SPEP2P list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-SPEP2P&A=1
DISCLAIMER:
Privileged and/or Confidential information may be contained in this message. If you are not the addressee of this message, you may not copy, use or deliver this message to anyone. In such event, you should destroy the message and kindly notify the sender by
reply e-mail. It is understood that opinions or conclusions that do not relate to the official business of the company are neither given nor endorsed by the company. Thank You.
To unsubscribe from the STDS-802-3-SPEP2P list, click the following link:
https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-SPEP2P&A=1
To unsubscribe from the STDS-802-3-SPEP2P list, click the following link: https://listserv.ieee.org/cgi-bin/wa?SUBED1=STDS-802-3-SPEP2P&A=1